No products
Passing contact switch with red lever. Provides the short burst of current needed to operate accessories such as point motors and some types of semaphore signal motors.
Passing contact switch with white lever. Provides the short burst of current needed to operate accessories such as point motors and some types of semaphore signal motors.
Passing contact switch with yellow lever. Provides the short burst of current needed to operate accessories such as point motors and some types of semaphore signal motors.
Switch console to neatly house up to six Peco switches from their PL-series (PL-26, PL-22 and PL-23) Switches not included.
Set of six switch mounting plates for countersinking Peco PL-series switches into a control panel or baseboard.
Pack contains 10 female spade connectors and 5 shrouds
Closed Microswitch Closed type, rated 16v 2amps (continuous) or 2.5amps (momentary). Use this microswitch with the PL-19 Microswitch Housing for polarity switching the SL-E790BH 0 Gauge Double Slip. Recommended to be used with PL-19 Microswitch Housing
Set of 2 Wiring Harness (Loom) for PL-10 Series Turnout Motors
For use with all solenoid motors (e.g. PL-10 and PL-11). Connect this unit to either a 16v AC or 12v DC supply on your transformer. The capacitor stores up power and discharges a 'kick' to ensure turnout blades 'snap over' every time.
Turnout switch module for use with Peco's PL-26 range of passing contact switches (not included). Enables switches to be connected without the need for any soldering. Power is supplied through the fitted leads and each switch is automatically connected when fitted.
Turnout Switch Module Add-on Use this add-on unit to extend Peco's PL-50 Switch Module Unit. This pack contains a single add-on unit.
Can be used with most plastics, ideal for motors an bearings.
Power Feed Joiners Code 100 & Code 124 8 power-feed rail-joiners (4x Red and 4x Black) : 8 inches (204mm) each PL-80 power feed joiners are compatible with Peco 00/H0 gauge Code 100 track (that is the standard Peco and Hornby track)and Peco 0 gauge Code 124 track with bullhead profile rail.
Power Feed Joiners Code 55/80 8 power-feed rail-joiners (4x Red and 4x Black) : 8 inches (204mm) each PL-82 power feed joiners are compatible with regular Peco N gauge Code 80 track and Peco Code 55 N gauge finescale track.
Set of 5x mounting plates for use with Peco PL-10E turnout motors.
Smartswitch 1m Cable Extension (Pack of 2)
Standard 6 pin decoder A decoder is a circuit board used for operating Digital models: it receives and interprets informations sent by the Controller.
Power and Signal Booster
The Hornby R8247 Accessory/Point Decoder can be programmed to accommodate four point motors or solenoid operated accessories, plus other electrical accessories that require a constant or delayed current flow, for example a turntable.
Train controller
Z21 DCC system Easy intuitive control on both mobiles and tablet computers. Split-screen allows you to control locomotives and accessories at the same time.
Slow action point motor. Suitable for most track.
Modern Image Tail Lamp (Flashing) Great little addition that adds realism to the back of your wagons or coaches. Detects motion and turns on automatically. Automatically turns off 4mins after last movement. No pick-up, wires or soldering required - LED plugs in. Can be fitted to brake vans, coaches, wagons etc. Runs for AGES on a standard button...
Flame Effect Tail Light (Flickering) Great little addition that adds realism to the back of your wagons or coaches. Detects motion and turns on automatically. Automatically turns off 4mins after last movement. No pick-up, wires or soldering required - LED plugs in. Can be fitted to brake vans, coaches, wagons etc. Runs for AGES on a standard button...
Spark-arc electric and Constant Outputs Great little addition that adds realism to the back of your wagons or coaches.
Coach Light (Constant) Great little addition that adds realism to the back of your wagons or coaches. Detects motion and turns on automatically. Automatically turns off 4mins after last movement. No pick-up, wires or soldering required - LED plugs in. Can be fitted to brake vans, coaches, wagons etc. Runs for AGES on a standard button battery. Includes...
Working OO/HO gauge LED buffer light for use with analogue or DCC layouts. No wiring needed - connects directly to rails.
Coach Lighting with Effect - Warm White/Flickering Tail Coach Lighting with included tail lamp - Warm white coach lighting and flickering red tail lamp Contents:1 x Lighting Strip (220mm) 1 x Set of LEDs 1 x Cell battery (20mm)Scale: Suitable for several scales
Flashing light effects Module Simulates four flashing effects used on a layout and is supplied with four suitable LED's
DCC Signal Controller for two-aspect signal lights (controls two sets) SC1 One-Touch DCCâ„¢ Signal Control Module - suitable for any gauge. This is a Colour Light Signal decoder module which enables almost any two-aspect LED signal to connect to your DCC controlled layout - very easy to set up and use. The module can control up to two pairs of separate LEDs...
DCC Control Unit for Dapol's motorised semaphore signals. This unit allows you to control your motorised Dapol semaphore signals via the keypad on your DCC controller. This unit has the capability to operate up to two single-arm signals and works with both OO and N gauge signals.
DCC Signal Controller Dual For Original Dapol Semaphore Signals
Diesel sound capsule WARNING! No battery included when shipped outside UK
Smart Light Party (Disco) The SL10 uses a mixture of lighting colours and flashes to simulate a party or disco in a house, nightclub or pub etc. This set simulates a party or disco in a nightclub, house or pub. The unit is pre-set to produce a mixture of flashes and colours.
Smart Light Random Randomly turns on and off simulating the lights in an office, house or town scene.
Smart Light Emergency Vehicle The SL30 adds a realistic blue or red and blue multi flashing light which can be fitted under the roof of a model emergency vehicle. It adds life to a scene! Realistic multi-flashing blue light which can be fitted under a roof light on police, ambulance and fire emergency vehicles.
Smart Light Real Fire Effect The SL40 realistically flickers shades of amber and yellow flames mixed with the red embers of a real fire. It adds life to a scene! Flickering shades of amber and yellow flames and the flickering red embers to form a realistic fire glow. Can be used for log fires, BBQ's and house fires.
Smart Light Arc Welding The SL50 shows bright white arc flashes followed by a slowly dimming red glow from the weld cooling down. It adds life to a scene! This set simulates a the effects of a arc welder hard at work. The sequence includes the flickering white light and the glow of the red to show the welder heating up. This item looks great in any...
Smart Light Television Simulator The SL60 fits inside a model house or shop and lights just like a TV with multiple colours and flickering. Adds life to a scene! Fit this unit into a shop window and watch as the flickering effects made the television come to life. This unit simulates the flickering of the telly with multiple colours and effects. A great...
Multi Gauge Track Tester for OO/O/G • Quickly tests track for power faults • Low cost and easy to use • Works on OO/HO , O gauge & G Gauge track and intervening gauges • Indicates DCC, DC polarity or fault • Checks point frogs • Multicolour LED shows DCC (orange), DC polarity (red or green) or power faults
Black Wire 100m (7 x 0.2mm)
Red Wire 10m
Wire Glue - Conductive paint If ordering from the European Union and outside the UK (for instance from Germany or France), this can only be sent to a residential address and not a business address, due to customs rules.
Sequencing light hub
Port sharing device