To make your model railway tunnels look more detailed and realistic, focus on texture, weathering and scenic...
No products
Wire Brown 7 x 0.2mm 10 Metres
Wire Blue 7 x 0.2mm 10 Metres
The Bachmann 36-565 Train Control System is for use with DC-Operated trains in N, OO, OO9, HO & ON30 Scale. Easy to use systemPower indicator lightPlug-in wiringOutput to track: 0.7ampsElectronic Circuit ProtectionDirection Control SwitchVariable speed dialUniversal track power wire included for other track systems
Set of 5x mounting plates for use with Peco PL-10E turnout motors.
Capacitor Discharge Unit
Small Reed Switch Max switching current 0.5amps (capacity 10VA)Max Voltage 220vACLength 18.5mm x 2.6mm
Passing contact switch with white lever. Provides the short burst of current needed to operate accessories such as point motors and some types of semaphore signal motors.
Passing contact switch with yellow lever. Provides the short burst of current needed to operate accessories such as point motors and some types of semaphore signal motors.
Point Extension Cable
Single Pole On/Off Switch Use this to control features such as lighting circuits, or as a section switch where only 1 controller is used.
5 decoders DCC25
6 Pin Decoder Socket with 8 Pin Plug x 3
Single Pole Changeover Switch (On/On) Use this to switch power from one device to another or for operating items such as 2 aspect colour light signals.
Z21 DCC system Easy intuitive control on both mobiles and tablet computers. Split-screen allows you to control locomotives and accessories at the same time.
Train controller
Set of six switch mounting plates for countersinking Peco PL-series switches into a control panel or baseboard.
Probe for operating turnout motors (use with PL-18)
Studs and Tag Washers, for use with probe 25 studs and 25 washers in a pack
Twin Track Cased Controller
6 pin decoder analogue compatible
5x3mm clear LED + 12V resistor
Turntable motorising kit Contains: Gearbox, shaft, batteries, battery holder, switch, cable & wiring diagram. Everything needed to motorize a model railway turntable
Power Connecting Clamp
Switch console to neatly house up to six Peco switches from their PL-series (PL-26, PL-22 and PL-23) Switches not included.
4 function decoderSize: 25.25mm x 16.6mm x 5.3mm (0.95” x 0.65” x 0.2”) Power Handling: 1.3A Motor Drive (2A peak), 4 light/switchable functions - each 150mA, 200mA max. Addressing: Address 3 preset, will accept any address between 1 and 9999. Harnesses: 90mm overall length, removable 9 pin JST, 8 pin NEM652 plug with wires dressed to UK standard. DC...
E-Z Command 8 Pin To 21 Pin Adaptor
Red Wire 10m
Black Wire 100m (7 x 0.2mm)
8 to 21 Pin Adaptor
2.5 Amps G scale Controller
Power and Signal Booster
21-pin 3-function 2-sided 1A decoder with back EMF for slow running DCC Ready. 21-pin socket
Single Track Panel Controller
OPTI small function decoderSize: 18.5mm x 10.5mm x 4.8mm (0.73” x 0.42” x 0.18”) Power Handling: 1.1A Motor Drive (1.6A peak), 4 light/switchable functions - each 150mA, 200mA max. Addressing: Address 3 preset, will accept any address between 1 and 9999. Harnesses: 90mm overall length, removable 9 pin JST, 8 pin NEM652 plug with wires dressed to UK...
Pack contains 10 female spade connectors and 5 shrouds
Train Control and Transformer
Grain of Wheat Bulb 12v Clear (Pack of 5) Scale / Type: Z / N / TT / HO / OO / O / Gauge 1 / G / Slot Cars Current draw for one bulb is approx 80ma
8 Pin Decoder Socket with Harness x 1
Very Small Locomotive Decoder 2 Function Most suited to OO/HO locomotives. Key features of this standard decoder include smooth operation, 14/28 speed steps, plug and play, transponder id-equipped, all mode programming, decoder reset CV, motor isolation protection, advanced consisting, 2 and 4 digit addressing and DCC compatability. this decoder is rated...
6 Pin N Gauge Plug-in Decoder Most suited to N Gauge locomotives. Key features of this standard decoder include smooth operation, 14/28 speed steps, plug and play, transponder id-equipped, all mode programming, decoder reset CV, motor isolation protection, advanced consisting, 2 and 4 digit addressing and DCC compatability. this decoder is rated at 1 amp...
Passing contact switch with red lever. Provides the short burst of current needed to operate accessories such as point motors and some types of semaphore signal motors.
8 Pin Decoder Blanking Plate (x10)