Pack of four 0.5" Risers - 24" long

WST1406
Woodland scenics

Totally flat areas of land are very rare in nature. They usually occur as part of human intervention when a large flat area is required. A prime example is the railway, which has large expanses of flat land in stations, good yards, dockyards, and so on.

Therefore, one way to add realism to your model railway layout is to make it look like it was carved out of undulating land with cuttings and embankments where necessary. This means that inside of your railway perimeter fence, you need to replicate the flat nature and gentle gradients of the railway itself. In many cases, these areas will be higher than baseboard level to allow the terrain of the land to be below the level of the railway as well as above.

A quick and easy way to create gentle gradients is to use this set of 4 sloping sections from Woodland Scenics. These are flexible in order that you can create sloping curves as well as straights. Simply use as many sections as are need to reach the required height above the baseboard. Each section in this pack will raise the level to ½” (13mm) over a length of 24” (610mm).

More details

In stock

ScaleSuitable for several scales

£ 15.00

Add to my wishlist

Ask about product
Pack of four 0.5" Risers - 24" long

WST1406
Pack of four 0.5" Risers - 24" long

Totally flat areas of land are very rare in nature. They usually occur as part of human intervention when a large flat area is required. A prime example is the railway, which has large expanses of flat land in stations, good yards, dockyards, and so on.

Therefore, one way to add realism to your model railway layout is to make it look like it was carved out of undulating land with cuttings and embankments where necessary. This means that inside of your railway perimeter fence, you need to replicate the flat nature and gentle gradients of the railway itself. In many cases, these areas will be higher than baseboard level to allow the terrain of the land to be below the level of the railway as well as above.

A quick and easy way to create gentle gradients is to use this set of 4 sloping sections from Woodland Scenics. These are flexible in order that you can create sloping curves as well as straights. Simply use as many sections as are need to reach the required height above the baseboard. Each section in this pack will raise the level to ½” (13mm) over a length of 24” (610mm).

 

More info

Pack of 4 foam risers.

Each one measures 1/2" Height x  2 1/2" Width x 24" Long (1.27cm x 6.35cm x 60.9cm).

Risers are generally used with Incline/Decline Starters to create varying grades on your layout. Risers are easily flexed to form curves and work on plywood or foam bases. To install, pin in place with Foam Nails and attach with Foam Tack Glue™ or Low Temp Foam Glue Gun and Glue Sticks.

There is no experience necessary to build a layout with The SubTerrain Lightweight System. No complicated calculations to make, no expensive power tools to buy and no dusty mess to clean up.

The revolutionary System consists of sturdy, durable and lightweight foam components that take the guesswork out of designing and building a layout, and Tools and Adhesives specifically designed to work with the System. The SubTerrain Manual gives modelers detailed, fully illustrated instructions for constructing a layout.

Watch the SubTerrain demonstration video :

Totally flat areas of land are very rare in nature. They usually occur as part of human intervention when a large flat area is required. A prime example is the railway, which has large expanses of flat land in stations, good yards, dockyards, and so on.

Therefore, one way to add realism to your model railway layout is to make it look like it was carved out of undulating land with cuttings and embankments where necessary. This means that inside of your railway perimeter fence, you need to replicate the flat nature and gentle gradients of the railway itself. In many cases, these areas will be higher than baseboard level to allow the terrain of the land to be below the level of the railway as well as above.

A quick and easy way to create gentle gradients is to use this set of 4 sloping sections from Woodland Scenics. These are flexible in order that you can create sloping curves as well as straights. Simply use as many sections as are need to reach the required height above the baseboard. Each section in this pack will raise the level to ½” (13mm) over a length of 24” (610mm).

 

  • Video - Refresh the page if the video is not showing below
  • Click on a thumbnail to load the video